Play Catapult

Building a snowball catapult is a hands-on way to prepare for the winter while spending quality time with your children as well as teaching them woodworking basics and simple physics. During the winter, they provide a fun opportunity for neighborhood competitions. A 4-foot-long catapult powered by a bungee cord has a range of 45 to 65 feet. You only need a few basic hand tools and a power drill to construct a snowball catapult.

Instructions

Frame

1

Cut the 2-by-4-inch lumber with the foxtail saw. You need two 24-inch lengths and two 48-inch lengths for the support frame, three 24-inch lengths for the uprights and one 48-inch length for the throwing arm.

2

Cut the plywood sheet into two 1-foot squares. One square is the throwing arm's pan. Cut the other square into two right triangles. These are the upright beams' support brackets.

3

Place two 48-inch lumbers flat on your work surface so that they are parallel and their outside edges are 24 inches apart. Place two 24-inch lumbers across the 48-inch lumber ends, making sure the four pieces form a perfect rectangle. Nail the rectangle together, using four nails for each corner.

Upright Beams

4

Lay two 24-inch upright beam lumbers flat on your work surface. Center a support bracket on the end of each upright beam so that the right angle points to its top and the base hangs over the bottom exactly 2 inches.

5

Place each upright beam onto the frame so that the tip of the support bracket's base is flush with the frame's front end. Drive three 2 1/2-inch nails through each support bracket into the frame. Drive three 3-inch nails through the frame into each upright.

6

Place the remaining 24-inch lumber across the top ends of the upright beams. Drive three 3-inch nails through the ends of this beam into the upright beams.

Throwing Arm

7

Lay the throwing arm flat on your work surface. Center the 1-foot plywood square on the throwing arm so that the square's edge is flush with the throwing arm's end. Attach the square to the throwing arm by driving four 2 1/2-inch nails through the square into the throwing arm.

8

Twist the C-hook into the throwing arm, 2 inches below the plywood square. The hook's end must point toward the throwing arm's top when it is fully screwed in.

9

Open the hinge. Place it against the 4-inch side of the throwing arm's bottom end. Attach the hinge by driving three wood screws through the holes into the throwing arm.

Final Assembly

10

Slide the throwing arm under the upright beams' crossbar. Center the hinge's free side on the rear of the frame's front beam. Fasten it to the beam with three wood screws.

11

Tie bungee cord's ends to the frame's front corners. Keep each end in place by placing two U-shaped nails over it and hammering them into the frame.

12

Raise the throwing arm to the cross bar. Stretch the bungee cord over the cross bar. Hook it into the C-hook.

• 
  

  How to Make a Catapult for Kids eHow

  www.ehow.com Crafts Other Craft Projects

  Making a catapult with your kids, for your kids to use and play with isn't as hard as you think. The key is to simplify and work on a smaller scale.. Other ...

• 
  

  Easy Backyard Catapult for Hero Dads - Instructables - Make, How ...

  www.instructables.com/id/Easy-Backyard-Catapult-for-Hero-Dads

  This is a catapult (ala torsion style) I built inspired from the video a contributor named schoondogs posted. His catapult looked simple enough so I ...

• 
  

  How to Build an Easy Catapult for Kids eHow

  www.ehow.com Education K-12 K-12 For Educators

  A catapult is basically a spring-loaded launcher which uses a lever and tension to propel an object. The catapult was invented by the Greeks in 399 B.C. and used ...

• 
  

  Origami for Kids Paper Airplanes

  www.origami-kids.com

  How to make Step by Step the Best Paper Airplanes of the World - Origami for Kids

• 
  

  How to make a catapult - Science Kits for Kids

  www.explorabox.org/activities/engineering/your-own-catapult

  How to make a catapult: using only two sets of wooden chopsticks, a rubber band, and duct tape. In this article well show you how to make a catapult that launches ...

• 
  

  21 Snow Sled Plans: How to Build Make Design Klondike Derby Sleds ...

  www.inquiry.net/outdoor/winter/gear/sleds

  Plans to make 21 Sleds, Sleighs, Toboggans, including a Boy Scout Klondike Derby Sled.

• 
  

  MAKE Projects

  makezine.com/projects

  Make: Projects. Explore our growing cookbook of DIY projects for the workshop, kitchen, garage, and backyard. Learn new skills, find family fun, build a robot or a rocket

• 
  

  How to Build a Catapult Toy- Catapult Wars Kit for kids - YouTube

  www.youtube.com/watch?v=sdYlD1vo_4c

  Build a Catapult! Learn how to assemble the Catapult Wars kit from the Boy Craft brand. Create two catapults and have a playful game with a friend! For ...

• 
  

  how to build a kids catapult - jimmythejock on HubPages

  jimmythejock.hubpages.com Arms and Weapons History

  HOW TO BUILD A CATAPULT . A catapult was a medieval rocket launcher it was used to hurl stones rocks and even tar covered rocks which had been set alight,they were ...

• 
  

  catapult - Knight for Hire - the son of a real knight offers his ...

  www.knightforhire.com/catapult.htm

  Catapults. home. WARNING: This information is circulated as a service to interested persons; no liability is accepted by Karl Kindt in relation to ...